Gas-Grill-Roasted Bone-In Pork Rib Roast
By America's Test KitchenPublished on December 13, 2012
Time
2 hours, plus 6 hours salting, 2 hours soaking, and 30 minutes resting
Yield
Serves 6 to 8
Ingredients
Before You Begin
If you buy a blade-end roast (sometimes called a “rib-end”), tie it into a uniform shape with kitchen twine at 1-inch intervals; this step is unnecessary with a center-cut roast. For easier carving, ask the butcher to remove the tip of the chine bone and to cut the remainder of the chine bone between the ribs. For instructions on carving the roast, see step-by-step below.
Instructions
- Pat roast dry with paper towels. If necessary, trim thick spots of surface fat layer to about ¼-inch thickness. Using sharp knife, cut slits in surface fat layer, spaced 1 inch apart, in crosshatch pattern, being careful not to cut into meat. Sprinkle roast evenly with salt. Wrap with plastic wrap and refrigerate for at least 6 hours, up to 24 hours.
- One to 2 hours before grilling, submerge wood chips in bowl of water to soak.
- Place soaked chips in 9-inch disposable aluminum pie plate and set on primary burner of grill (burner that will stay on during grilling). Position cooking grates over burners. Turn all burners to high and heat grill with lid down until very hot, about 15 minutes. Turn primary burner to medium-high and turn off other burner(s). Scrape grate clean with grill brush.
- Sprinkle roast evenly with pepper. Place roast on grate with meat near, but not over, primary burner and bones facing away from heat. Open top vents halfway and cover grill, positioning vents over meat. (Initial grill temperature should be about 425 degrees.) Grill roast until instant-read thermometer inserted into thickest part of meat registers 140 degrees, 1¼ to 1½ hours.
- Transfer roast to carving board, tent loosely with foil, and let rest for 30 minutes (internal temperature should rise to about 150 degrees). Carve into thick slices by cutting between ribs. Serve, passing salsa separately (if using).
Time
2 hours, plus 6 hours salting, 2 hours soaking, and 30 minutes restingYield
Serves 6 to 8Ingredients
Test Kitchen Techniques
Ingredients
Test Kitchen Techniques
Ingredients
Test Kitchen Techniques
Why This Recipe Works
We chose the loin’s center-cut roast for our bone-in pork rib roast recipe for its great ease of preparation: Because the meat is a single muscle attached along one side to the bones, there was no need to tie the roast for a tidy presentation. Salting the meat extracted much of the pork roast’s liquid, which ensured that our pork roast recipe would produce a deeply browned, crisp crust. Grilling the pork, covered, on the cooler side of the grill allowed the meat to cook through slowly by indirect heat without risk of burning the exterior.
Before You Begin
If you buy a blade-end roast (sometimes called a “rib-end”), tie it into a uniform shape with kitchen twine at 1-inch intervals; this step is unnecessary with a center-cut roast. For easier carving, ask the butcher to remove the tip of the chine bone and to cut the remainder of the chine bone between the ribs. For instructions on carving the roast, see step-by-step below.
Instructions
- Pat roast dry with paper towels. If necessary, trim thick spots of surface fat layer to about ¼-inch thickness. Using sharp knife, cut slits in surface fat layer, spaced 1 inch apart, in crosshatch pattern, being careful not to cut into meat. Sprinkle roast evenly with salt. Wrap with plastic wrap and refrigerate for at least 6 hours, up to 24 hours.
- One to 2 hours before grilling, submerge wood chips in bowl of water to soak.
- Place soaked chips in 9-inch disposable aluminum pie plate and set on primary burner of grill (burner that will stay on during grilling). Position cooking grates over burners. Turn all burners to high and heat grill with lid down until very hot, about 15 minutes. Turn primary burner to medium-high and turn off other burner(s). Scrape grate clean with grill brush.
- Sprinkle roast evenly with pepper. Place roast on grate with meat near, but not over, primary burner and bones facing away from heat. Open top vents halfway and cover grill, positioning vents over meat. (Initial grill temperature should be about 425 degrees.) Grill roast until instant-read thermometer inserted into thickest part of meat registers 140 degrees, 1¼ to 1½ hours.
- Transfer roast to carving board, tent loosely with foil, and let rest for 30 minutes (internal temperature should rise to about 150 degrees). Carve into thick slices by cutting between ribs. Serve, passing salsa separately (if using).
Gift This Recipe
Enjoyed this dish? Let others know by sharing it as a gift recipe.
Key Equipment
Keep Exploring
0 Comments